The 2012 Toyota Camry has a standard halogen headlight bulb. The low beam headlight bulb is H11 and the high beam is 9005. The fog light bulbs are also 9005.
As for the taillights, the brake light bulb is 21/5W, the turn signal is 3057 and the backup light is 921.
If you’re looking to replace the tail light bulbs on your 2012 Toyota Camry, you’ll need to know what size bulbs to buy. Here’s a quick rundown of the different sizes for the various types of tail light bulbs on the Camry:
– Low beam headlight: H11
– High beam headlight: 9005
– Tail light: 7443
– Brake light: 3157
2012 Toyota Camry Tail Light Bulb Replacement
If your 2012 Toyota Camry is in need of a new tail light bulb, don’t fret – replacing it is a quick and easy process. Here’s how to do it:
1. Open up the trunk of your Camry.
There are two screws that hold the taillight assembly in place – remove these with a Phillips head screwdriver.
2. Once the screws are removed, gently pull the taillight assembly away from the car so you can access the back of it.
3. Locate the burned out bulb and twist it counterclockwise to remove it from its socket.
4. Insert the new bulb into the socket, twisting it clockwise until it’s snug.
How Do You Change a Taillight Bulb on a 2012 Toyota Camry?
Assuming you need to change the driver side taillight:
1. Open the trunk and locate the two screws near the taillight.
2. Remove these screws with a Phillips head screwdriver.
3. Gently pull back on the taillight assembly to release it from its housing. There are three plastic tabs that hold it in place – two on top and one on bottom.
4. Reach behind the assembly and unplug the electrical connector.
You may have to wiggle it a bit to get it loose.
5. Remove the old bulb by gently twisting it counterclockwise until it comes out of the socket.
6 Install the new bulb by inserting it into the socket and twisting clockwise until tight.
What Size Tires Goes on a 2012 Toyota Camry?
Assuming you would like tire sizes for the 2012 Toyota Camry: The 2012 Toyota Camry comes with P215/60R16 tires as standard equipment.
How Do You Change a Rear Light Bulb on a Toyota Camry?
When it comes to changing a rear light bulb on a Toyota Camry, the process is actually quite simple. All you need is a Phillips head screwdriver and a new light bulb. To begin, open up the trunk of your Camry and locate the two screws that are holding the taillight assembly in place.
Once you have located these screws, use your screwdriver to remove them.
With the screws removed, you should now be able to pull the taillight assembly away from the car. Be careful when doing this, as there are still electrical connections that need to be disconnected before completely removing the assembly.
There are three different types of bulbs in the rear lights of a Camry – brake lights, turn signals, and reverse lights.
To change the brake light bulb, simply twist it counterclockwise and pull it out of its socket. Replace with a new bulb (make sure it is properly seated in its socket) and then twist clockwise to secure it in place.
Repeat this process for both turn signal bulbs. To change the reverse light bulb, there is a small access panel that needs to be removed first.
Use your screwdriver to remove the two screws holding this panel in place and then carefully pry it off.
The reverse light bulb is located behind this panel – simply twist counterclockwise and pull out to remove it. Again, replace with a new bulb making sure that it is properly seated before twisting clockwise to secure it into place.
How Do I Know My Headlight Bulb Size?
If you’re not sure which headlight bulb size your car uses, there are a few ways to find out. One way is to check your car’s owner’s manual. This should list the types of bulbs used for the headlights, as well as other areas of the car.
Another way to find out is to look for a label on the back of the headlight assembly. This should also list the correct bulb size. Finally, you can take a measuring tape and measure the diameter of the headlight housing.
Once you have this measurement, consult a chart that lists common bulb sizes and their corresponding measurements. With this information, you should be able to determine what size headlight bulb your car uses.
How to replace brake bulb and other bulb on Toyota Camry 2012 to 2017 (DIY) you can do it
Conclusion
The 2012 Toyota Camry uses a 9006 tail light bulb. You can purchase this bulb at most auto parts stores.