2011 Suburban Tail Light Bulb

The 2011 Suburban has a light bulb for the tail light that is easy to replace. The first step is to open the back hatch and locate the two screws that hold the lens in place. Once these screws are removed, the lens can be carefully pried off.

There will be three bulbs inside the housing, one for each side of the car and one for the center brake light. The bulbs can be removed by twisting them counterclockwise. To install the new bulbs, twist them clockwise into place.

Be sure to not touch the glass of the new bulbs with your fingers, as this will cause them to burn out prematurely. After all three bulbs have been replaced, snap the lens back into place and screw it in securely. Test your work by turning on the car’s headlights and depressing the brake pedal to make sure all three lights are working properly.

If your 2011 Suburban is anything like ours, then the tail light bulbs are probably starting to go out. We’ve noticed that they seem to last about a year or so before they need to be replaced. Thankfully, changing them is pretty easy and only takes a few minutes.

To start, you’ll want to open up the back hatch and locate the two screws that hold the taillight assembly in place. Once you’ve removed those, you can pull the assembly forward and access the bulbs. There are three bulbs in total – two brake lights and one reverse light.

Changing them is as simple as twisting out the old bulb and screwing in a new one. We always keep a few extra bulbs on hand, just in case one goes out while we’re on the road. And that’s it!

Once you’ve replaced all of the bulbs, just put everything back together and you’re good to go.

2011 Suburban Headlight Bulb Size

Looking for the headlight bulb size for your 2011 Suburban? Here’s what you need to know! The halogen headlight bulbs on your 2011 Suburban are H11.

You can find this information in your owner’s manual or on the back of the headlight assembly. This is the standard size for most vehicles, so you should be able to find this bulb at any auto parts store.

What is the Z71 Package on a 2011 Suburban?

The Z71 package is an optional extra that can be added to the 2011 Suburban. It includes a number of off-road focused features, such as a heavier duty suspension, skid plates and all-terrain tires. This makes the Suburban more capable when driving on rough or unpaved roads.

It’s worth noting that the Z71 package is only available on the 4WD version of the Suburban.

How Do You Change a Brake Light on a 2010 Chevy Suburban?

Assuming you need to replace a brake light and not just change a burnt out bulb, the process is as follows: 1. Open the rear hatch and locate the two screws that hold the taillight assembly in place. 2. Remove the screws with a Phillips head screwdriver and carefully pull the entire assembly away from the vehicle.

3. Unplug the wiring harness from the back of the taillight by depressing the tab on top of the connector and pulling it apart. 4. Reverse these steps to install a new taillight assembly.

What Kind of Oil Does a 2011 Chevy Suburban Take?

The 2011 Chevy Suburban takes 5W-20 oil.

Does a 2011 Suburban Take Synthetic Oil?

Yes, a 2011 Suburban can take synthetic oil. In fact, many newer vehicles are designed to specifically require synthetic oil. Check your owner’s manual to be sure before making the switch, but synthetic oil typically provides better protection for your engine and may even improve fuel economy.

2007-2013 GM Suburban / Silverado Pickups rear taillight Repair/replace


If your 2011 Suburban is equipped with LED tail lights, you may have noticed that they don’t last as long as traditional bulbs. In fact, it’s not uncommon for them to burn out after just a few years. Fortunately, there are a few things you can do to extend their life.

First, make sure to clean the lenses regularly. This will help prevent dirt and debris from build up, which can cause the lights to overheat and fail prematurely. Secondly, avoid exposing the lights to direct sunlight for extended periods of time.

This can also cause them to overheat and fail prematurely. Finally, if you do notice one of the LEDs burning out, replace it immediately. Don’t wait until all of the LEDs are burned out before replacing them, as this will likely result in having to replace the entire assembly.

Leave a Comment

Your email address will not be published. Required fields are marked *