The 2011 Hyundai Sonata has a tail light bulb socket that is located in the trunk. The socket is behind the liner and can be accessed by removing the liner. The bulb socket has a retaining clip that must be released in order to remove the old bulb.
To install the new bulb, reverse these steps.
If you’re like most people, you probably don’t think about your car’s tail light bulb socket very often. But if you have a 2011 Hyundai Sonata, you might want to take a closer look at it. That’s because there have been reports of the tail light bulb socket melting on these vehicles.
The problem seems to happen when the tail lights are turned on for an extended period of time, such as when the car is being driven in reverse. This can cause the socket to overheat and melt, which can lead to problems with the tail lights themselves.
If you have a 2011 Hyundai Sonata, it’s important to check your tail light bulb socket regularly.
If you see any signs of melting or damage, be sure to replace the socket right away. Taking this simple step could save you from having bigger problems down the road.
2011 Hyundai Sonata Tail Light Socket Replacement
If you’re like most drivers, you take pride in your car. You keep it clean, inside and out, and you perform routine maintenance to keep it running smoothly. So when a problem arises, it’s natural to want to fix it as quickly as possible.
If you’ve noticed that one of your tail light sockets is no longer working, don’t despair. Replacing a tail light socket is a relatively easy task that can be completed in just a few minutes.
Here’s what you’ll need:
– A new tail light socket (available at most auto parts stores)
– A Phillips head screwdriver
– A flathead screwdriver
– Wire cutters (optional)
Replacement Procedure:
1. Open the trunk of your car and locate the affected taillight assembly.
2. Using the Phillips head screwdriver, remove the screws that secure the taillight assembly to the car body. 3. Carefully pull the taillight assembly away from the car body far enough to access the electrical connections at the back of the unit. 4. Locate the faulty socket and disconnect it from its wiring harness by depressing the release tab and pulling firmly on the connector until it comes free 5 .
How Do You Change a Taillight Bulb on a 2011 Hyundai Sonata?
Assuming you need to change the driver side taillight:
1. Open the trunk and locate the two screws that hold the taillight assembly in place.
2. Remove the screws with a Phillips head screwdriver and pull the entire assembly out from the car.
3. Unplug the harness from the back of the taillight assembly by pushing on the tab and pulling it out.
4. Find the correct replacement bulb for your Sonata (in this case, it would be an LED).
5. Insert the new bulb into place, making sure it’s locked in properly, then reattach and plug in the harness.
How Do You Remove a Brake Light Bulb from the Socket?
Assuming you would like tips for removing a brake light bulb from the socket:
To remove a brake light bulb from the socket, firstly make sure to disconnect the power by disconnecting the negative battery terminal. This is to avoid any electrical shorts.
Next locate the bulbs, which are usually found near the taillights. Once located, use a small screwdriver or other tool to twist and remove the bulb from its socket. If there is any resistance when trying to remove it, then gently wiggle it back-and-forth until it comes loose.
Finally, once it is removed, clean out any debris in the socket before inserting a new bulb.
How Do You Remove the Brake Light on a Hyundai Sonata?
Assuming you would like tips on how to change a brake light on a Hyundai Sonata:
To change the brake light on your Hyundai Sonata, you will need:
– A new brake light (can be purchased at most auto stores)
– A Phillips head screwdriver
First, open your trunk and locate the two screws that are holding the brake light assembly in place. Using your screwdriver, remove these screws and carefully pull the assembly out.
There may be wires still attached to the back of the brake light, so be careful not to break them as you remove it.
Once the old brake light is removed, take your new one and insert it into the assembly. Make sure it is secured in place before reattaching the entire assembly to your car with the screws.
Test your new brake light by turning on your headlights and depressing the brakes – if it is working properly, you should see the new bulb illuminate.
How Do You Change a Taillight Bulb on a 2009 Hyundai Sonata?
If one of your taillights has burned out on your 2009 Hyundai Sonata, don’t despair. Replacing a taillight bulb is a relatively easy task that you can do yourself in just a few minutes. You’ll just need to gather a few tools and supplies before getting started.
Here’s what you’ll need:
– A new taillight bulb (the same type that was originally installed in your car)
– A Phillips head screwdriver
– A flathead screwdriver (optional)
– A friend or family member (optional)
Now that you have everything you need, follow these steps to replace the burnt out taillight bulb:
1. Open the trunk of your car and locate the two screws holding the taillight assembly in place. Remove these screws with your Phillips head screwdriver.
2. Gently pull the taillight assembly away from the car until it comes loose.
Be careful not to drop it or damage any of the wires attached to it.
3. Locate the burnt out bulb inside the assembly and twist it counterclockwise to remove it from its socket.
4. Insert the new bulb into the socket, making sure it’s twisted clockwise until tight.
Tail light socket replacement #1
Conclusion
If your 2011 Hyundai Sonata is in need of a new tail light bulb, you may be wondering how to change it. The process is actually quite simple and can be done in just a few minutes. First, open the trunk and locate the tail light assembly.
Next, remove the two screws that hold the assembly in place. Once the screws are removed, you will be able to access the bulb socket. To remove the old bulb, simply twist it counterclockwise and pull it out.
To install the new bulb, insert it into the socket and turn it clockwise until it is snug. Finally, replace the tail light assembly and screw it back into place.