Looking for a 2007 Mazda CX-7 tail light? You’re in luck! Here at PartsGeek.com, we carry a wide selection of tail lights for your Mazda CX-7.
Whether you’re looking for a replacement tail light or an upgrade to LED, we’ve got you covered. We even have smoked and clear lens options to give your CX-7 the look you want.
If you’re in the market for a used Mazda CX-7, there are a few things you should know about its tail light. First, the 2007 model is equipped with LED tail lights, which are significantly brighter than traditional incandescent bulbs. This can be a major advantage if you often drive in low-light conditions or at night.
Secondly, the CX-7’s tail light is integrated into the vehicle’s body design, so it can be difficult to replace if it becomes damaged. If you do need to replace the tail light on your CX-7, be sure to use an authorized Mazda dealer or another reputable source to get the correct part.
Mazda Cx-7 Tail Light Cover Replacement
If your Mazda CX-7 is in need of a new tail light cover, don’t fret – it’s an easy fix! In this blog post, we’ll walk you through the process of replacing a tail light cover on a Mazda CX-7. This project should take no more than 30 minutes to complete.
What You’ll Need:
– 1x Philips head screwdriver
– 1x Flathead screwdriver
– 1x New tail light cover (matching your vehicle’s make, model, and year)
Tools:
-1x set of pliers (optional)
Step 1: Open Your Car’s Hood & Locate the Tail Light Cover
Before getting started, open up your car’s hood to gain access to the back of the tail light assembly. Once you’re under the hood, locate the two screws that secure the taillight cover in place – one at the top and one at the bottom.
loosen these screws with a Phillips head screwdriver until they’re loose enough to remove by hand. Keep in mind that there may also be a third screw located in the middle of the taillight assembly; if so, loosen this one as well.
Step 2: Remove The Old Tail Light Cover & Install The New One
With all three screws loosened (or removed), gently pull off the old taillight cover being careful not to break any ofthe plastic tabs that hold it in place. If any of these tabs do break, don’t worry – they can easily be repaired with some super glue or epoxy resin. Once you have removedthe old cover, line upthe new one withthe holes forthe screws and lightly press it into place.
Be sure that all three tabs are properly aligned before moving on to step 3.
What are the Dimensions of the 2007 Mazda Cx 7 Tail Light
Assuming you are referring to the taillight assembly and not just the bulb, the dimensions are as follows: Width: 7.5 inches Height: 5.0 inches
How Many Bulbs Does the 2007 Mazda Cx 7 Tail Light Have
The 2007 Mazda Cx 7 has two bulbs in the tail light.
What is the Function of the 2007 Mazda Cx 7 Tail Light
The purpose of the 2007 Mazda Cx 7 tail light is to increase the visibility of the vehicle to other drivers on the road. The tail light is located at the rear of the vehicle and helps other drivers see the car from behind, especially when it is dark or foggy outside. The tail light also contains a brake light that illuminates when the driver presses down on the brake pedal, warning other drivers that the car is stopping.
Where is the 2007 Mazda Cx 7 Tail Light Located
Assuming you’re talking about the taillight on the driver’s side of the vehicle, it is located just to the left of the brake light.
How Do You Replace a Burned Out Bulb in the 2007 Mazda Cx 7 Tail Light
Assuming you are referring to a taillight and not a headlight:
To replace a burned out bulb in the 2007 Mazda Cx 7 tail light, first open the trunk. There are two covers on the inside of the trunk that need to be removed in order to access the bulbs.
To remove the covers, use a flathead screwdriver to pry them off. Once the covers are off, there are three bulbs that need to be unscrewed and replaced. The bulbs are held in place by screws, so use a Phillips head screwdriver to remove them.
Replace each bulb with a new one and screw it back in place. Once all three bulbs have been replaced, put the covers back on and close the trunk.
MAZDA CX-7 REAR TAIL LIGHT REMOVAL REPLACEMENT CX7
Conclusion
The 2007 Mazda CX-7 has a unique and stylish tail light design that really sets it apart from other SUVs on the market. Unfortunately, this cool feature can also be a bit of a pain when it comes to replacing a burned out bulb. Thankfully, our friends at Mazda have put together a helpful video tutorial on how to change the tail light bulbs on your CX-7.
Check it out below!