2007 Jeep Commander Tail Light Bulb: The Jeep Commander is a large SUV that was introduced in 2006. It has a V8 engine and seating for up to seven passengers. The commander is available with either four-wheel drive or two-wheel drive.
The tail light bulb on the commander is located in the rear of the vehicle. It is a halogen bulb that emits a bright white light.
If your Jeep Commander is like most vehicles on the road these days, its tail light bulbs are probably made of LEDs. But what happens when one of those bulbs burns out? You might be tempted to just drive without a tail light, but that’s not safe.
And changing the bulb is actually pretty easy, even if you’ve never done it before.
Here’s a quick guide to changing a 2007 Jeep Commander tail light bulb:
1. Open the hatch and locate the taillight assembly.
On the back of the assembly, there will be a plastic cover that needs to be removed in order to access the bulbs.
2. Once the cover is off, twist each bulb counterclockwise and pull it out of its socket.
3. Insert the new bulb into the socket and twist it clockwise until it’s tight.
4. Put the cover back on and close up the hatch. You’re all set!
2007 Jeep Commander Brake Light Bulb Size
If you’re looking to replace the brake light bulb in your 2007 Jeep Commander, you’ll need a #3157NA light bulb. This can be found at most auto parts stores.
What is the Best Way to Change a 2007 Jeep Commander Tail Light Bulb
Assuming you are talking about the brake/tail light:
The first step is to open the rear hatch and locate the two screws that hold the tail light housing in place. Once these screws are removed, you will be able to pull the entire housing away from the Jeep.
Next, locate the black power connector and disconnect it from the bulb socket. With the power connector disconnected, you can now twist and remove the bulb socket from the housing. At this point, you can install the new bulb into the socket and reassemble everything in reverse order.
How Do I Know If My 2007 Jeep Commander’S Tail Light Bulbs Need to Be Changed
It’s easy to tell when your Jeep Commander’s tail light bulbs need to be changed – just take a look at them! If the bulbs are dim, flickering, or have burned out completely, then it’s time for new ones. You can also check your owner’s manual for specific guidance on how often to change your tail light bulbs.
Can I Use Any Type of Bulb in My 2007 Jeep Commander’S Tail Lights
If you have a 2007 Jeep Commander, you can use any type of bulb in your tail lights as long as it is the correct size and wattage. You can find the correct size and wattage for your vehicle in your owner’s manual or by contacting a Jeep dealership.
What are the Consequences of Not Changing a Burned Out Tail Light Bulb in My 2007 Jeep Commander
If you don’t change a burned out tail light bulb in your 2007 Jeep Commander, you could get pulled over. A taillight is required by law so that other drivers can see your car from behind, and a burned out bulb means that the taillight isn’t working properly. If you’re pulled over, you could be given a ticket or even arrested.
In addition, not changing a burned out tail light bulb is just plain dangerous and irresponsible.
How to remove rear taillights and bulbs Jeep Commander
Conclusion
If your Jeep Commander is from 2007, then you might be in need of a new tail light bulb. This blog post will give you a step-by-step guide on how to change the bulb so that you can avoid any accidents on the road. first, locate the fuse box under the hood and open it up.
Then, find the fuse labeled “taillights” and pull it out. Next, locate the two screws that are holding the taillight assembly in place and remove them. After that, carefully pull out the assembly and disconnect the electrical connector.
Now, you can twist out the old bulb and insert a new one. Finally, put everything back together in reverse order and test it out before hitting the road again.