The 2002 Cadillac Seville has a tail light bulb that is easy to change. The first step is to open the trunk and locate the two screws that hold the taillight assembly in place. Next, remove the screws and pull the assembly away from the car.
There will be a wire connector attached to the back of the assembly, so be sure to disconnect it before removing the entire unit. Finally, twist out the old bulb and replace it with a new one.
If you’re like most people, the thought of changing a tail light bulb on your car probably seems like a daunting task. But don’t worry – it’s actually not that difficult! Here’s a step-by-step guide to changing a 2002 Cadillac Seville tail light bulb:
1. Open the trunk and locate the taillight assembly. On the 2002 Cadillac Seville, the taillight assembly is located on the driver’s side of the car.
2. Remove the two screws that secure the taillight assembly in place.
3. Pull out the taillight assembly and disconnect the electrical connector.
4. twist counterclockwise and remove the old bulb from its socket . Insert a new # 3157NAK tail light bulb into socket , then rotate it clockwise to lock it in place .
Reconnect electrical connector .
5 reinsertthe whole assembly back into place and screw it in securely .
2002 Cadillac Seville Tail Light Bulb Replacement
Assuming you need to replace a tail light bulb on a 2002 Cadillac Seville:
To access the bulbs, open the trunk and remove the two screws securing the plastic panel above the taillight. Pry out the panel to expose the bulbs.
Turn each bulb counterclockwise to remove it from its socket. Insert a new bulb in each socket and turn it clockwise until it locks into place. Reattach the plastic panel and screw it back into place.
How Do I Replace a Burned Out Tail Light Bulb on My 2002 Cadillac Seville
If one of the tail light bulbs on your 2002 Cadillac Seville has burned out, you’ll need to replace it as soon as possible. Tail light bulbs are required by law in most states, so it’s not worth risking a ticket by driving with a burned out bulb. Fortunately, changing a tail light bulb on this model of Cadillac is easy to do and only takes a few minutes.
To start, open up the trunk and locate the taillight assembly. There are two screws that hold the assembly in place – remove these screws with a Phillips head screwdriver. Once the screws have been removed, carefully pull the entire assembly away from the car body.
There will be three wires connected to the back of the taillight assembly – disconnect these by gently pushing down on the locking tab and pulling each wire connector off.
Now that you have access to the back of the taillight lens, you’ll see two black plastic covers held in place by small metal clips. These clips must be pried open in order to access the bulbs inside.
Use a flathead screwdriver or something similar to pry open each clip (it may take some force), then carefully remove each black cover. Behind each cover is a single tail light bulb – twist counterclockwise to remove an old bulb, then insert a new one (twist clockwise until tight). Be sure to handle new bulbs with care, as they can easily be damaged if dropped or mishandled.
Once both new bulbs are in place, simply reverse all steps above to reassemble everything and get back on the road!
What Type of Bulbs are Used for the Tail Lights on a 2002 Cadillac Seville
Tail lights on a 2002 Cadillac Seville use incandescent bulbs.
Why Have My Tail Lights Stopped Working on My 2002 Cadillac Seville
If your tail lights have stopped working on your 2002 Cadillac Seville, it is likely due to a problem with the tail light bulb, the fuse, or the wiring. First, check to see if the bulbs are burned out. If they are, replace them with new bulbs.
Next, check the fuse for the tail lights. If it is blown, replace it with a new fuse. Finally, check the wiring for the tail lights.
If there is a break or loose connection in the wiring, repair or replace it as necessary.
LED 194 bulb replacement 2003 Cadillac SLS
Conclusion
If your 2002 Cadillac Seville has a tail light bulb that needs to be replaced, follow these steps. First, open the trunk and locate the two screws that hold the taillight assembly in place. Remove these screws with a screwdriver and pull the assembly away from the car.
Second, twist off the old bulb and insert a new one in its place. Be sure to match the size and wattage of the new bulb to the old one. Finally, reattach the taillight assembly and screw it back into place.