The 1995 Toyota Camry was equipped with a standard tail light. The light was located on the rear of the vehicle, near the center. It consisted of a bulb that emitted a red light, and a lens that protected the bulb.
When the brake pedal was depressed, the tail light would illuminate, warning drivers behind the Camry to slow down.
When it comes to vehicles, one of the most important parts is the tail light. Not only is it a required safety feature, but it also helps you stay visible on the road. If your tail light isn’t working properly, it could lead to an accident.
That’s why it’s important to know how to change a 1995 Toyota Camry tail light.
The first step is to open the trunk and locate the taillight assembly. There are two bolts that hold it in place, so remove those with a wrench or socket set.
Once the bolts are removed, you can carefully pull out the entire assembly.
Once you have access to the bulb, twist it counterclockwise until it comes loose from the socket. Then, insert the new bulb into the socket and twist it clockwise until tight.
Finally, replace the taillight assembly and tighten down the bolts.
That’s all there is to changing a 1995 Toyota Camry tail light! Be sure to check your lights regularly to ensure they are functioning properly.
1995 Toyota Camry Tail Light Bulb Replacement
If your 1995 Toyota Camry is like most cars on the road, the tail light bulbs need to be replaced about once a year. Here’s how to do it:
First, open the trunk and locate the two screws that hold the taillight assembly in place.
Remove these screws and pull the assembly out far enough so that you can access the bulbs.
Next, twist off the old bulb and insert a new one in its place. Be sure to match up the correct size and type of bulb – there are usually different types for brake lights and turn signals.
Once the new bulb is in place, screw the taillight assembly back into place and close the trunk. You’re done!
How Much is It to Fix a Tail Light on a Toyota Camry?
The cost to fix a tail light on a Toyota Camry will vary depending on the severity of the damage and where you take it to be repaired. If it is just a minor crack or chip, then you can probably get away with repairing it yourself with a kit from your local auto parts store. However, if the damage is more severe, such as a large crack or hole, then you will need to take it to a professional body shop for repair.
The cost for this type of repair will range from $100-$300, depending on the extent of the damage.
How Do You Change a Brake Light on a 1995 Toyota Camry?
Assuming you need to replace a burnt out brake light:
You will need to open the trunk and locate the two screws that hold the taillight assembly in place. Once these are removed, you can carefully pull the assembly away from the car.
There will be a rubber grommet holding the wiring in place, which you can disconnect. The entire light assembly can now be removed.
There are three bulbs in the assembly – two for tail lights and one for the brake light.
To remove a bulb, twist it counterclockwise and pull it out of its socket. You can now insert the new bulb – again, twisting it counterclockwise until it is tight. Be sure to not touch the glass of the new bulb with your fingers, as this will cause it to burn out prematurely.
Reconnect everything in reverse order and test your brake light before driving!
Are Brake Lights Easy to Replace?
Brake lights are an important safety feature on your vehicle, so it’s important to make sure they’re in good working order. If one of your brake lights has gone out, you’ll want to replace it as soon as possible.
Fortunately, brake lights are relatively easy to replace.
In most cases, you can do it yourself with just a few tools. Here’s a step-by-step guide to replacing a brake light:
1. Start by opening the trunk or tailgate of your vehicle.
Locate the brake light assembly and remove the screws that hold it in place.
2. Pull the old bulb out of the socket and insert a new one. Make sure the new bulb is seated securely in the socket before screwing the assembly back into place.
3. Test your new brake light by turning on your headlights and depressing the brake pedal. If everything looks good, you’re all set!
How to Replace Tail Lights 95-96 Toyota Camry
Conclusion
The 1995 Toyota Camry came with a new design for the tail light. The old design had the brake light and turn signal in one unit, while the new design had them separated. This change was made to improve safety and make it easier for drivers to see the turn signals.
Some people think that this change was unnecessary, but it is a good safety feature.